Mechanical Engineering Multiple Choice Questions
Mechanical Engineering Multiple Choice Questions
Our top 50 Mechanical Engineering questions and answers focus on all the areas of this subject. It covers over more than 50 topics in Mechanical Engineering. Anyone who wishes to sharpen their knowledge, preparing for the interviews, or preparing for the entrance exam can practice these Mechanical Engineering Questions.
1) What we call the resistance of a material against any external force.
Malleability
Stiffness
Hardness
Strength
Answer: D [ Strength ]
Description: Strength is a mechanical property of the material under which it resists change in its dimension shape and any failure by applying any external force.
2) Which hardness test uses the steel ball as indenter?
Rockwell C hardness test
Brinell Hardness test
Rockwell B hardness test
Vickers hardness test
Answer: B [ Brinell Hardness Test ]
Description: Steel ball is used as an indentor in the Brinell hardness test.
3) In which test, the specimen will be used in the form of the supported beam?
Charpy Test
Brinell Test
Izod test
Rockwell hardness test
Answer: C [ Izod Test ]
Description: Izod test is like the Charpy test, but the Izod geometry consists of a cantilever beam with the notch located on the same side as the impact point.
4) Which metal from the following has the non-crystalline structure?
Quartz
Silica Glass
Tungsten
Iron
Answer: B [ Silica Glass ]
Description: Generally, metals exist in crystalline form. The ceramic compound-silica (SiO2), can exist either in a crystalline form or in a non-crystalline form (amorphous form). Silica's non-crystalline (amorphous) form is just called silica glass.
5) Which of the following has less crystallinity?
Nickel
Iron
Low-density polythene
High-density polythene
Answer: C [Low-Density Polythene ]
Description: Iron and nickel, metals, possess a crystalline form, whereas high-density polyethylene (HDPE) and low-density ethylene (LDPE) are a class of polymers. These thermoplastics are semi-crystalline, out of which LDPE exhibits a crystallinity of about 50-60% and HDPE of about 90%. Some people may term HDPE as crystalline, but it is more appropriate to restrict it in the category of semi-crystalline class.
6) Which of the following axis system is being satisfied by tetragonal crystal system?
a ≠ b ≠ c, α = β = ϒ = 90°
a = b ≠ c, α = β = ϒ = 90°
a = b = c, α ≠ β = ϒ = 90°
a = b = c, α = β = ϒ = 90°
Answer: B [a = b ≠ c, α = β = ϒ = 90°]
Description: Tetragon has two sides equal and all angles equal
7) Which one of the following is least symmetrical?
Simple Cubic
Triclinic
Monoclinic
Tetragonal
Answer: C [ Triclinic ]
Description: In the triclinic crystal system, we observe all the sides and angles to be unequal (a ≠ b ≠ c and α ≠ β ≠ γ ≠ 90°), thus giving the least symmetry (1-fold symmetry) among all 7 Bravais Lattices.
8) ASTM stands for?
American Society for Testing and Materials
American Society for Tool Measurement
American Society for Tensile Material
American Society for Tensile Measurement
Answer: A [ American Society for Testing and Materials ]
Description: ASTM stands for American Society for Testing and Materials. ASTM develops technical standards for a wide range of materials products. American Society for Tensile Measurement is used to decide various standards in tensile measurement.
9) What is the scale range of the Mohs hardness test?
1 - 10
1 - 1000
100 - 200
1 - 3000
Answer: A [ 1- 10 ]
Description: Mohs hardness scale was developed by "Frederich Mohs" in 1822, a chart that denotes the various materials' relative hardness (1-softest to 10-hardest). According to the Mohs scale, diamond is the hardest material, and talc is the softest material.
10) What is the first step involved in the process of preparing test samples for microstructural examination?
Fine grinding
Rough polishing
Etching
Fine polishing
Answer: A [ Fine grinding ]
Description: Fine grinding involves using abrasive silicon carbide to get a flat surface, i.e., nearly free of the disturbed or deformed scratches introduced in the previous sample preparation step.
11) Etching of specimen is done to achieve _______
Invisible grain boundary
Visible grain boundary
Hardness
Toughness
Answer: B [ Visible Grain Boundary ]
Description: Etching is done to obtain a visible grain boundary. It is a surface treatment process.
12) Which equipment can be used for the inspection of the inside portion of the hollow chamber or narrow tube?
Telescope
Endoscope
Flexiscope
Borescope
Answer: D [ Borescope ]
Description: A borescope is used for visual of the inside portion of the hollow chamber.
13) Which of the following property is the fine-grained structure?
Corrosion resistance
Ductility
Hardness
Creep resistance
Answer: B [ Ductility ]
Description: Finer the grain size (lower the grain size), more is the number of grain boundaries. Thus more is the yield strength; thus, more is the flexibility. This is the reason why we can easily draw a fine-grained structure into wires.
14) Which penetrating liquid is used for the liquid penetration test?
Fluorine based solvent
Petroleum-based carrier fluid
Chlorine-based solvent
Water
Answer: B [ Petroleum-based carrier fluid ]
Description: In a liquid penetration test, either petroleum-or-water-based carrier fluids are used as solvents or cleaners according to the type of penetrant used. The petroleum-based carrier fluid is a penetrating liquid in a liquid penetration test and fluorescent red color dye for visible light.
15) Which of the following non-destructive testing is used to detect the change in the composition of any material?
Ultrasonic Test
Liquid penetration test
Radiography
Eddy current test
Answer: C [ Radiography ]
Description: It enables us to detect the change in composition. X-rays or γ-rays are used in radiography techniques.
16) What is the melting point of iron (in ℃)?
1535
1410
910
768
Answer: A [ 1535 ]
Description: The melting point of iron in degree centigrade is 1535℃.
17) What is the Iron-Carbon phase diagram?
Unary phase diagram
Binary phase diagram
Tertiary phase diagram
Ternary phase diagram
Answer: B [ Binary phase diagram ]
Description: Binary phase diagrams are based on two-component systems. Here, the two components may be mixed in an infinite number of different proportions, which indicates that composition also becomes a variable, along with pressure and temperature. The iron-carbon phase diagram, Pb-Sn diagram are the best examples of this category.
18) Which of the following reaction does not exhibit a mushy zone in the Fe-C phase diagram?
Peritectic reaction
Eutectic reaction
Peritectoid reaction
Eutectoid reaction
Answer: B [ Eutectic ]
Description: A mushy zone is nothing but a solid-liquid mix in a two-phase region. The alloys or reactions, which exhibit lower melting points than the two pure metals, are known as eutectic alloy systems taking eutectic reactions that do not exhibit mushy zone.
19) Which of the following material has the carbon varying from 2.1 to 4.3%?
Mild steel
Dead steel
Cast iron
Medium carbon steel
Answer: C [ Cast-Iron ]
Description: Cast irons are the alloy of iron and carbon that contains 2.1 to 4.3% C, along with other varying amounts of silicon and manganese. This varying carbon range makes them easily castable, asking them to call cast irons.
20) Which of the following material has the carbon varying from 4.3 to 6.67%?
Mild Steel
Pig Iron
Cast Iron
Medium carbon steel
Answer: B [ Pig Iron ]
Description: Pig iron contains a very high carbon content, usually varies from 4.3 to 6.67%. The pig iron is called so, as it resembles the shape of a reclining pig.
21) Which equation represents the Gibbs phase rule?
F = C - P + 2
F = C + P + 2
F = C + P - 1
F = C + P + 1
Answer: A [ F = C - P + 2 ]
Description: The Gibbs phase rule is represented as F = C - P + 2, where F = number of intensive degrees of freedom, P = number of phases, and C = the minimum number of independent constituents.
22) The invariant reaction involving a liquid phase decomposing into two different solids on cooling is known as _____
Eutectic point
Eutectoid point
Peritectoid point
Peritectic point
Answer: A [ Eutectic point ]
Description: Explanation: The eutectic invariant reaction, in general, can be represented as:
L → S1 + S2
L represents the liquid of eutectic composition, and S1 and S2 are two different solids of fixed composition each.
23) The Line joining a liquid phase with liquid and solid phase mixture is known as ________
Solidus
Liquidus
Solvus
Tie line
Answer: B [ Liquidus ]
Description: Liquidus is the line joining liquid phase with liquid and solid phase mixture.
24) The line joining a solid phase with liquid and solid phase mixture is known as ________
Solidus
Liquidus
Solvus
Tie Line
Answer: A [ Solidus ]
Description: Solidus is the line joining liquid phase with liquid and solid phase mixture.
25) Cast iron is a product of _______
Bessemer converter
Cupola
Blast Furnace
Open hearth furnace
Answer: B [ Cupola ]
Description: The cupola furnace (a modified blast furnace) can melt cast irons, bronzes, etc. Cast irons have a carbon content of 2-4% and have low melting temperatures, making them easily castable.
26) Wrought iron is a product of ______
Bessemer converter
Cupola
Puddling furnace
Blast furnace
Answer: C [ Puddling furnace ]
Description: The puddling furnace creates wrought iron (nearly pure iron) from the pig iron. The wrought iron is tougher and malleable.
27) Which of the following induces fine-grain distribution in alloy steel?
Vanadium
Nickel
Titanium
Manganese
Answer: A [ Vanadium ]
Description: Vanadium is the most used grain refiner in steel. It forms a microscopic precipitate particle in steel, which acts as pinning agents, thus obstruct grain growth at higher temperatures, encouraging new grains to nucleate.
28) Tensile strength of alloy steel can be improved by adding ______
Vanadium
Nickel
Titanium
Manganese
Answer: B [ Nickel ]
Description: Nickel can improve tensile strength as well as the toughness of alloy steel. Small additions of niobium (Nb) also increases the tensile strength of carbon steel.
29) Which of the following is the hardest constituent of steel?
Austenite
Ledeburite
Martensite
Bainite
Answer: C [ Martensite ]
Description: Martensite is the hardest constituent of steel. The primary reasons for the internal strains within BCC iron are the excess of carbon and the plastic deformation of parent FCC iron surrounding the martensitic plate. The cooling rate and the amount of carbon in steel are directly proportional to the hardness achieved in martensitic transformation.
30) Iron possesses BCC crystal structure up to (in degree centigrade)?
768
910
1410
1539
Answer: A [ 768 ]
Description: Pure iron possesses either BCC or FCC crystal structure as its temperature increases from room temperature to its melting point. At room temperature to 910° C, it has BCC, between 910° C and 1410° C it has face-centered cubic, and from 1410° C to its melting point (1539° C), it returns to its BCC crystal structure.
31) Which of the following form of iron is magnetic?
α
δ
γ
λ
Answer: A [ α ]
Description: The alpha form of iron is magnetic and stable at all temperatures, i.e., below 910° C.
32) Which of the following methods is best for examining surface flaws on the castings?
Magnetic particle inspection
Pressure test
Acoustic emission test
Visual Inspection
Answer: D [ Visual Inspection ]
Description: Visual inspection is a type of non -destructive testing technique that provides a means of detecting and examining the variety of surface flaws, such as surface finish, discontinuities, and surface cracks on the castings. This method is very cheap and widely used because most surface defects and roughness can be easily observed.
33) Which of the following types of light is preferred for using fluorescent penetrant in liquid penetrant testing (LPT) method?
Monochromatic Light
Normal Light
Red Light
Ultraviolet Light
Answer: D [ Ultraviolet light ]
Description: In the LPT method, the objective is accomplished by entrapment of the inspection liquid by the flaws followed by visual inspection of the surface under ultraviolet light (when using a fluorescent penetrant), and for visible dye penetrant normal light can be used for the inspection process.
34) Which of the following processes is preferred for preparing aluminum ingots for the liquid penetrant testing method?
Caustic etching
Machining
Acid pickling
Grinding
Answer: C [ Acid Prickling ]
Description: When the liquid penetrant test is used for aluminum ingots, before the test, the surfaces of the aluminum ingots are prepared or treated with the acid pickle. This process is known as acid pickling, and it is recommended in preference to all other processes like caustic etching, machining, etc.
35) Which of the following inspections is used for detecting invisible surface defects in a nonmagnetic casting?
Dye penetrant inspection
Visual inspection
Ultrasonic inspection
Radiography examination
Answer: A [ Dye penetrant inspection ]
Description: The dye penetrant inspection method is mainly used to detect invisible surface defects in a nonmagnetic casting. The casting is cleaned by brushing, and then spraying or dipping of the casting is done into a dye containing a fluorescent material. Then for inspection, casting is dried and viewed in the darkness that reveals the discontinuities in the surface.
36) Which of the following methods is best for detecting interior flaws in the castings?
Visual inspection
Liquid penetrant test
Ultrasonic inspection
Magnetic particle inspection
Answer: C [ Ultrasonic Inspection ]
Description: In the ultrasonic inspection, a beam of high-frequency sound waves is introduced into the material to detect interior flaws in the material. The sound wave travels through the material with some loss of energy and is reflected at the interfaces. It will be further analyzed to define the presence and location of flaws in the casting.
37) Which of the following was not a classification of a subject taking the MFFT?
Slow in-accurate
Slow accurate
Reflectives
Fast-Accurates
Answer: B [ Slow accurate ]
Description: The subjects taking the MFFT, the subjects were then classified into four categories, namely, fast-accurates, reflectives, impulsive and slow-inaccurate. Slow-accurates were not one of the classifications.
38) Which of the following parameter is used to assess the magnetic ability of a material?
Magnetization
Magnetic flux density
Susceptibility
Magnetic dipole moment
Answer: D [ Susceptibility ]
Description: Magnetic susceptibility is a measure to quantify a material's ability to undergo magnetization in an applied magnetic field. It is the ratio of magnetization (M) to the applied magnetic field intensity (H).
39) With an increase in temperature, the resistance of a semiconductor _________
Decreases
Increases
Remains Constant
First increases and then decreases
Answer: A [ Decreases ]
Description: Semiconductors have a negative temperature coefficient of resistance; thus, resistance increases with decreasing temperature.
40) What is the polymerization of two or more chemically different monomers forming a long molecular chain?
Copolymerization
Addition Polymerization
Chain growth polymerization
Condensation polymerization
Answer: A [ Copolymerization ]
Description: Copolymerization involves the polymerization of two or more different monomers to form a long chain molecule. A well-known 'Nylon 66' is a copolymer of hexamethylenediamine and adipic acid.
41) Which of the following is a secondary bond network of thermoplastics?
0-Dimensional
1-Dimensional
2-Dimensional
3-Dimensional
Answer: B [ 1-Dimensional ]
Description: Thermoplastics have a one-dimensional network of '2-degree' secondary bonds.
42) Which of the following are ceramics solids?
Non-metallic, organic, and amorphous solids
Non-metallic, inorganic, and crystalline solids
Metallic, inorganic, and amorphous solids
Non-metallic, inorganic, and amorphous solids
Answer: D [ Non-metallic, inorganic and amorphous solids ]
Description: Ceramics are non-metallic, inorganic, amorphous solids and are mostly oxides of metals. Ceramics possess low tensile strength and are brittle.
43) For an M10 grade RCC (Reinforced Cement Concrete), the cement ratio to aggregate to the sand is?
1:3:4
1:2:3
1:2:6
1:3:6
Answer: D [ 1:3:6 ]
Description: M10 grade of RCC have cement to aggregate to sand ratio equal to 1:3:6.
44) Which one of the following can act as a modifier in the glass-forming process?
Sodium oxide
Silicon dioxide
Phosphorous oxide
Magnesium oxide
Answer: D [ Magnesium oxide ]
Description: Magnesium oxide is used as a viscosity modifier, making glass melt viscosity in the desired range for proper formation of the filaments.
45) Which of the following is not a laminar composite?
Cladding
Bimetallic
Wood
Paints
Answer: C [ Woods ]
Description: Wood is not a laminar composite. Bimetallic, cladding, and paints are considered laminar composites.
46) In sandwich composites, which of the following material can be used for filling purposes?
Polymer
Wood
Cement
All of them
Answer: D [ All of them ]
Description: Wood, cement, and polymer can be used to fill the gap in sandwich composites.
47) Which of the following has a greater impact on the longitudinal strength of reinforced composites?
Fiber strength
Fiber orientation
Fiber diameter
Fiber length
Answer: A [ Fiber Strength ]
Description: Longitudinal strength of reinforced composites is directly proportional to their fiber strength.
48) Angle between side cutting edge and end cutting edge in the top surface plane of the tool.
Side relief angle
Side rake angle
Nose angle
Side cutting edge angle
Answer: D [ Nose Angle ]
Description: Nose angle is the angle between side cutting edge and end cutting edge.
49) What is the maximum allowed value of VB in mm for the HSS tool used with the cast iron workpiece for rough machining?
1
0.5
2
1.5
Answer: C [ 2 ]
Description: VB denotes the width of wear land. Maximum 2mm width of wear land is allowed in flank wear.
50) Which of the following tools is most suitable for very hard and brittle material?
Cast-cobalt alloy
HSS
Carbides
None of them
Answer: C [ Carbides ]
Description: Carbides are very hard and have very good red hot hardness properties, hence most suitable for machining hard and brittle material.
Comments
Post a Comment